Peugeot 208 Key Replacement

Peugeot 208 key replacement is best left to professional auto locksmiths who have the appropriate equipment and know-how. They will be able to make and program new keys much quicker than a dealership and at a lesser cost.

If your key fob has stopped locking or unlocking your doors, it could be due to a dead coin battery. There are also other reasons for the key to be malfunctioning.

Dead Coin Battery

A dead battery in the coin compartment will hinder your Peugeot 208 from locking or unlocking, and won't start the engine. If this is the scenario, you'll need utilize the backup starting method that is described in the owner's manual of your vehicle.

The spark plugs might also be worn out. The spark plugs ignite fuel to start the engine. However they have a short time of life. If they aren't used enough and they fail, they'll eventually die.

There is a simple solution to this problem. Check the voltage of the battery with a multimeter. If it's below 11.5 volts it is time to replace it. If the battery has corroded, it is important to clean its contacts. You can do this by lifting the rubber covers that protect the two terminals on the battery and using a wire brush to remove any parts that are corroded from the battery. You should then reconnect the cables to the positive and negative poles.

Water Damage

If your 208 won't turn on and the battery is not flat, then you need to make sure whether the spark plugs are working. It is possible that they are just overly dirty, which causes them not to spark. This can be easily corrected by cleaning the spark plugs in an workshop.

Peugeot cars have transponder keys that works with the car's ignition system. This ensures that only the correct key is able to turn the engine. If the chip inside the Peugeot key is damaged, it won't send the correct signal to the vehicle.

This is a very common issue that can be caused by water damage. This is especially prevalent in colder climates, as the vehicle might have been exposed to rain or snow. In this situation, contact a reliable locksmith who has the required tools and equipment to modify the key. They will also have the most up-to-date technology and the machinery needed to make the Peugeot 208 smart key. The process shouldn't take longer than 15 minutes.

Contacts to the battery are not working properly.

Peugeot changed from the old carbon encased transponder chips and introduced a new type of chip that relies on electronic components on a circuit board. The new system is great in its initial state, but the circuit boards deteriorate over time and cease to function properly.

This can stop the immobiliser chip from working which means that your car won't start. Contact an Peugeot specialist, or a locksmith, if this is the case.

A common issue is when the battery in the key fob begins to fail. This causes the blade of the key to stop feeding into the lock. A locksmith from your vehicle can replace the battery and cut a new blade for you, this is normally a quick fix.

Faulty Receiver Module

It could be that the receiver module has a problem in the event that your Peugeot key fob isn't working after being dropped on the floor, exposed to a sudden storm or accidentally washed. The receiver module is responsible for transmitting radio frequencies to the onboard computer that controls the central locking system of your Peugeot vehicle.

https://www.g28carkeys.co.uk/peugeot-car-key-replacements-near-me/ on the key fob keep water from getting to the electronic chip. The chip can be damaged by water if it is exposed to the water for an extended period of time. The high salt content in the ocean water or pool could cause damage to the key fob when it is submerged.

If your Peugeot spare key fob isn't working, you'll need to have the module replaced. This can only be done by an expert auto locksmith or Peugeot specialist. Unlike other cars, Peugeot keys are protected by an exclusive immobilizer system that requires the correct programming to begin the engine. This is why you should only be able to trust a professional Peugeot locksmith to handle the task of programming and creating a replacement.

Computer with a problem on board

The on-board computer in your Peugeot is responsible for a variety of the systems inside your vehicle, from power windows to airbags. The computer on board will display the code when something goes wrong. This code will be saved in the system until the issue is resolved. This may require the on-board computers to be replaced.

The most common reason for the warning light for airbags to flash is corrosion or loose connections within the sensor. This can occur due to wear and tear, aging, or exposure to salt and moisture. It is important to have this issue resolved as soon as possible, since an airbag that is not functioning properly could be risky in the event of an accident.

If you encounter an error message stating that the card is not found on your Peugeot key fob, the battery in the key fob could be dead or weak. This will stop the key fob sending a signal to disarm the vehicle's immobilizer. You can test this by pressing the unlock button on the key fob and then attempting to start your car. If it doesn't work the battery on the key is in need of replacement.