Peugeot 208 Key Replacement
Peugeot 208 key replacement should be left to experienced auto locksmiths who have the appropriate equipment and technical knowledge. They can design and program keys more quickly and at a lower cost than dealerships.
A dead coin battery is most likely to be the cause when your key fob stops locking or unlocking doors. There are also other reasons why the key may be malfunctioning.
Dead Coin Battery
A dead coin battery will prevent your Peugeot 208 from locking or unlocking, and cannot start the engine. In this case you'll need to choose the alternate method to start that is described in the owner's manual.
The spark plugs may also be worn out. The spark plugs are responsible for igniting the fuel that ignites the engine. They have a limited lifespan. They will eventually break down if they aren't used frequently enough.
Luckily, there is an easy solution to this issue. The best solution is to check the voltage of your car battery with a multimeter. If it's below 11.5 volts and you are not satisfied, then it is time to replace it. If the battery is damaged, it is important to clean its contacts. This can be done by removing the rubber cover from the two terminals on the battery and then using a wirebrush to remove any parts of the battery that are corroded. After that, you need to connect the positive pole cables to the negative.
Water Damage
If your 208 doesn't start and the battery is not running, then make sure whether the spark plugs are functioning. You might find that they are filthy and don't spark. This is easily fixed by cleaning the spark plugs in a workshop.
Peugeot automobiles use a key with a transponder compatible with the immobiliser. This ensures that only the right key can turn the engine. If the chip inside the Peugeot key is damaged then it will not transmit the correct signal to the vehicle.
Water damage is a typical reason for this issue. This is a common problem in more cold climates where the car has been exposed to snow or rain. In this case, you need to contact an experienced locksmith who has the tools and equipment required to modify the key. https://www.g28carkeys.co.uk/peugeot-car-key-replacements-near-me/ have the latest technological know-how and machinery required to make the Peugeot 208 smart key. The process should take no more than 15 minutes.
Contacts for the battery that are defective
Peugeot changed from the old carbon encased transponder chips to a brand new type of chip that incorporates electronic components within circuit boards. This new system works great when it's new, however, over time, the circuit boards begin to wear out and stop functioning correctly.
This can stop the immobiliser chip from working, so your car won't start. If this is the case it's a good idea to seek out a Peugeot specialist or locksmith.
Another issue that is common is when the battery for the key fob gets depleted, which causes the key blade to stop from entering the lock. A locksmith in your car can replace the battery and cut a new blade for you, this is normally a quick fix.
Faulty Receiver Module
It could be that the receiver module is defective when your Peugeot key fob stops working after being dropped on the floor, or exposed to a sudden downpour or accidentally washed. The receiver module is responsible for transmitting radio signals to the onboard computer that regulates the central locking system of your Peugeot vehicle.
The key fob itself has rubber seals that prevent water from getting to the chip inside. Water can damage the chip when it is exposed to the water for an extended period of time. Submerging the key fob in the ocean at the beach or throwing it into the pool can be especially damaging because of the high salt content.
If your Peugeot spare key fob doesn't work, you'll need to have the module replaced. This can only be done by a Peugeot specialist or an expert auto locksmith. Unlike other cars, Peugeot keys are protected by an immobilizer that is unique and requires the correct code to begin the engine. This is why you should only be able to trust a professional Peugeot locksmith to take on the job of creating and programming the replacement.
Computer on board is not working properly
The on-board computer of your Peugeot is responsible for various systems inside your car, including airbags and power windows. The on-board computer will display the code when something goes wrong. This code is stored inside the system and stays there until the issue is resolved. Most often, this involves replacing the computer on board.
One of the most frequent reasons for the airbag light turning on is the loose or corroded connections within the airbag sensor. This could be due to wear and tear, aging, exposure to salt and moisture. It is essential to have this issue addressed as quickly as you can, as a malfunctioning airbag can be risky in the event of an accident.
If you find the error "card not found" on your Peugeot, the key battery inside the key fob may be weak or dead. This will stop the key fob from sending a signal that will disable your vehicle's immobilizer. You can test this by pressing the unlock button on the key fob, then attempting to start your vehicle. If this fails it is likely that the battery will need replacing.