Peugeot 208 Key Replacement

It is best to leave the replacement of Peugeot keys for 208 to auto locksmiths equipped with the equipment and know-how. They can create and program new keys faster than a dealership would and at a lower cost.

If your key fob has stopped locking or unlocking your doors, it is likely due to a dead coin battery. There are other causes for the key to be malfunctioning.

Dead Coin Battery

A dead battery can stop your Peugeot 208 from locking and unlocking, as well as hindering it from starting the engine. If this is the situation, you'll need apply the backup starting technique that's described in the owner's manual to your vehicle.

The spark plugs could also be worn out. The spark plugs are responsible for instigating the fuel that powers the engine. They have a limited life span. If they're not used enough, they will eventually fail.

There is a straightforward solution to this issue. The best solution is to test the voltage of your car battery with a multimeter. If the voltage falls below 11,5 volts, it's the time to replace it. If the battery is damaged it is necessary to clean its contacts. This can be accomplished by removing the rubber covers from the two terminals on the battery and then using a wirebrush to eliminate any corroded battery parts. After that, you need to connect the positive pole cables to the negative.

Water Damage

If your 208 does not start and the battery hasn't gone flat, you should check the spark plugs. You may find that they're dirty and do not spark. This can be fixed by cleaning the spark plugs in the workshop.

Peugeot cars use keys that are transponder-type and works with the car's immobiliser system. This ensures that only the correct key can turn the engine. If the chip inside the Peugeot key is damaged, it will not send the correct signal to the vehicle.

Water damage is a frequent cause of this problem. This is particularly common in colder climates, as the vehicle may have been exposed to rain or snow. In this case, you need to contact a trusted locksmith who will have the tools and equipment required to change the key's programming. They also have the latest technological know-how and machinery required to create the Peugeot 208 smart key. The process should not take more than 15 minutes.

Contacts with the battery may be damaged.

Peugeot replaced the transponder chips with a new type that uses electronic components that are mounted on a circuit board. The new system works great when it's new, but the circuit boards wear out over time and cease to function properly.

This can stop the immobiliser chip activating which means that your car won't start. If this happens, it's recommended to call a Peugeot specialist or locksmith.

A common issue occurs when the battery of the key fob begins to fail. This causes the blade of the key to stop feeding into your lock. A locksmith for cars will replace the battery, and then cut a new blade for you. This is a simple fix.

Faulty Receiver Module

If your Peugeot key fob isn't working after dropping it on the floor, or being exposed to a sudden downpour or accidently washing it or washing it, it could be due to a faulty receiver module. The receiver module is responsible for transmitting radio signals to the onboard computer that manages the central locking system of your Peugeot vehicle.

The key fob itself has rubber seals that prevent water from reaching the electronic chip inside. However, prolonged exposure to water could penetrate these seals and damage the chip. Submerging the key fob in sea water at the beach or throwing it into the pool could be especially damaging because of the high salt content.

If your Peugeot spare key fob isn't working You'll need the module replaced. https://www.g28carkeys.co.uk/peugeot-car-key-replacements-near-me/ is only performed by a professional auto locksmith or Peugeot specialist. Unlike other cars, Peugeot keys are protected by a unique immobilizer system that requires the correct coding to start the engine. This is the reason why you should only choose a reputable Peugeot locksmith with the task of programming and creating a replacement.

Computer with a problem on board

The on-board computer inside your Peugeot is responsible for a variety of the systems inside your car, ranging from airbags to power windows. The on-board computer will show a code if something goes wrong. This code is stored in the system and will remain there until the issue is resolved. This can often mean that the on-board computers to be replaced.

One of the main causes of the light flashing is loose or corroded connection in the airbag sensor. This can be caused by wear and tear, aging or exposure to salt and moisture. It is crucial to get this issue resolved as soon as you can, as an airbag that is malfunctioning can be dangerous in the event an accident.

If you notice an error message that says "card not found" on your Peugeot, the key battery inside the key fob might be weak or dead. This will prevent the key fob from transmitting a signal that will disable your vehicle's standard immobilizer. Test this by pressing the unlock key on the key fob and then trying to start your car. If this doesn't work it is because the battery of the key needs to be replaced.