Peugeot 208 Key Replacement
It is best to leave the replacement of Peugeot 208 keys to auto locksmiths with the required equipment and knowledge. They will be able to create and program new keys quicker than a dealership and at a lower cost.
A dead battery for your coin is most likely to be at fault when your key fob stops locking or unlocking doors. There are other reasons the key could be malfunctioning.
Dead Coin Battery
A dead coin battery will stop your Peugeot 208 from locking or unlocking and will not start the engine. In this scenario you'll need employ the alternate method of starting as described in your vehicle's owner's manual.
Another reason your 208 might not be starting is because the spark plugs are been worn down. The spark plugs ignite fuel to start the engine. However they have a short time of life. They will eventually break down if they aren't used frequently enough.
There is a straightforward solution to this problem. Examine the voltage of your battery using a multimeter. If the voltage falls below 11,5 volts, then it's time to replace it. It is also essential to clean the battery's contacts if it has corrosion. This can be done by removing the rubber covers from the two battery terminals and then using a wirebrush to clean any damaged parts of the battery. After that, you need to connect the positive pole cables to the negative.
Water Damage
If your 208 doesn't start and the battery has not failed, you should examine the spark plugs. It could be that they're overly dirty, which causes them not to spark. The spark plugs can be cleaned in an workshop.
Peugeot cars are equipped with a key with a transponder that is compatible with the immobiliser. This ensures that only the correct key can turn the engine. If the chip inside the Peugeot key is damaged, then it won't transmit the correct signal to the vehicle.
This is a frequent issue that can be caused by water damage. This is a common problem in colder climates where the vehicle is exposed to rain or snow. If this is the case, you should seek out a reputable auto locksmith who has all the equipment and tools needed to modify the new key. They will also have the most up-to-date technology and the machinery needed to create a Peugeot 208 smart key. The process shouldn't last more than 15 minutes.
Contacts for the battery that are defective
Peugeot changed from the old carbon-encased transponder chips and introduced a new type of chip that relies on electronic components on a circuit board. The new system is great when it's new, however the circuit boards deteriorate over time and stop working properly.
This could prevent the immobiliser from working, so your vehicle will not start. Contact a Peugeot specialist or a locksmith if this is the situation.
A common issue occurs when the battery of the key fob starts to fail. This causes the blade of the key to stop feeding into your lock. A locksmith from your vehicle can replace the battery and cut a fresh blade for you, this is usually a simple fix.
Faulty Receiver Module
It could be that the receiver module is defective If your Peugeot key fob fails to function after being dropped on the floor, exposed to a sudden storm or accidentally washed. The receiver is responsible for sending radio frequency signals to an on-board computer, which controls the central locking system in your Peugeot vehicle.
The rubber seals on the key fob stop water from getting to the electronic chip. The chip can be damaged by water when exposed to water for a prolonged period of period of. Submerging the key fob into sea water at the beach or throwing it into the pool could be especially damaging because of the high salt content.
If your Peugeot spare key fob stops working then you'll have to get the module replaced. This can only be completed by an experienced auto locksmith or Peugeot specialist. Peugeot keys unlike other automobiles, are secured by an immobilizer system. This requires the correct codes to start the car. This is why you must go with a knowledgeable Peugeot locksmith with the task of programming and creating the replacement.
Computers with faulty on-board computers
The on-board computer in your Peugeot is responsible for a number of the systems inside your vehicle, from power windows to the airbags. The on-board computer displays a code if something goes wrong. This code is saved in the system and stays there until the issue has been resolved. This will often require the on-board computers to be replaced.
The most common cause of the airbag warning light to flash is corrosion or loose connections within the sensor. https://www.g28carkeys.co.uk/peugeot-car-key-replacements-near-me/ can be caused by wear and tear, age or exposure to salt and moisture. It is essential to have this issue addressed as soon as possible, as an airbag that is not functioning properly could be risky in the event of an accident.
If your Peugeot is showing a card detected as not present error, the battery inside the key fob may be dead or weak. This will stop the key fob sending a signal that will disable the vehicle's immobilizer. Try this by pressing the unlock button on the key fob, and then trying to start your vehicle. If this fails the battery on the key needs to be replaced.