Oregon Scientific BAR310HG User Manual

Download: http://manpurrlisle.hotelsvr.ru/?dl&keyword=oregon+scientific+bar310hg&source=pastelink.net

For international inquiries, please visit: www2. Initiate a sensor search on the main unit to start receiving temperature data from the sensor. The built-in barometer will measure humidity indoors.

По опыту эксплуатации, заряда одной батарейки хватает более чем на год. The unit contains no user-serviceable parts.

Oregon Scientific BAR310HG User Manual - Реализована подсветка, она включается при длительном нажатии на кнопку.

NOTE Please keep this manual handy as you use your new product. CLOCK OVERVIEW FRONT VIEW 1 4 5 6 2 3 1. MEM: Viewcurrent, maximum and minimum temperature 5. CH: Switch remote sensor display BACK VIEW 1 2 3 4 5 6 1. RESET: Reset unit to default settings 2. PRESSURE: Select pressure unit; set altitude 3. Sensor reception icon 5. Sensor battery low 6. Clock reception icon 8. Alarm mode icon 10. Main unit battery low 12. Battery compartment cover 4. Press RESET after each battery change. NOTE Do not use rechargeable batteries. We recommended that you use alkaline batteries with this product for longer usage and lithium batteries in temperatures below freezing. WALL MOUNT Remove the stand at attach as shown. The main unit can collect data from up to 3 sensors. To set up the sensor: 1. Remove the battery door. Reset after each battery change. Make sure you use a different channel for each sensor. Close the battery compartment. Place the sensor next to the main unit. Initiate a sensor search on the main unit to start receiving temperature data from the sensor. Secure the sensor in the desired location using the table stand or wall mount. The transmission range may vary depending on many factors. You may need to experiment with various locations to get the best results. Because of this they will freeze in low temperatures of approximately -12°C 10°F. Disposable Lithium batteries have a much lower threshold for temperature with an estimated freezing range of below -30°C -22°F. Wireless ranges can be impacted by a variety of factors such as extremely cold temperatures. Extreme cold may temporarily reduce the effective range between the sensor and the base station. SENSOR DATA TRANSMISSION The sensor reception icon shows the status. Search for the sensor or check batteries To search for a sensor: Simultaneously, press and hold MEM and CH for 2 seconds. NOTE If the sensor is still not found, check the batteries, obstructions, and remote unit location. The clock collects the radio signals whenever it is within 1500 km 932 miles of a signal. RECEPTION SIGNAL To enable and force a signal search: Press and hold for 2 seconds. To disable the signal reception: Press and hold for 2 seconds. Clock signal reception indicator: STRONG SIGNAL WEAK SIGNAL NO SIGNAL SET CLOCK If the clock signal reception is enabled and a signal is being received the clock does not need to be manually set.. Press and hold MODE for 2 seconds. Press or to change the settings. If you have disabled the clock signal reception i. NOTE The language options are English E , German D , French F , Italian I , and Spanish S. ALARM To set the alarm: 1. Press to enter alarm mode. Press and hold for 2 seconds. Press to display alarm time. BAROMETER Barometer readings from the past 24 hours are stored by the main unit and used to provide weather forecast. To select barometer measurement unit: Press PRESSURE to toggle between mb and inHg. Press and hold PRESSURE for 2 seconds. Use and to set the altitude in 10 M 33 ft increments from -100 m -328 ft to 2500 m 8202 ft. NOTE The maximum operating altitude for the barometer and weather forecast is 2500m 8202 ft. WEATHER FORECAST This product forecasts the next 12 to 24 hours of weather within a 30-50 km 19-31 mile radius based on barometric pressure trend readings. To view outdoor sensors temperature readings: Press CH. To auto-scan between sensors: Press and hold CH for 2 seconds. To end auto-scan: Press CH. To toggle between current, minimum and maximum records for the selected sensor: Press MEM repeatedly. To clear the records: Press and hold MEM for 2 seconds. TEMPERATURE, HUMIDITY AND PRESSURE TRENDS The trend icons are based on recent readings. RISE STEADY FALL RESET To return to the default settings press RESET. PRECAUTIONS This product is engineered to give you years of satisfactory service if you handle it carefully. If you spill liquid over it, dry it immediately with a soft, lint-free cloth. Doing so will invalidate the warranty on the unit and may cause unnecessary damage. The unit contains no user-serviceable parts. Do not mix new and old batteries. Collection of such waste separately for special treatment is necessary. SPECIFICATIONS TYPE DESCRIPTION MAIN UNIT L x W x H 86 x 28 x 159. ABOUT OREGON SCIENTIFIC Visit our website www. The website also includes contact information for our Customer Care department in case you need to reach us, as well as frequently asked questions and customer downloads. For international inquiries, please visit: www2.
При появлении товара в нашем магазине Вам придет СМС с его ценой! Secure the sensor in the desired location using the table stand or wall mount. Добавлю еще, спустя четыре года. Отображение информации - цифры и символы, выбор единиц измерения. В системе есть возможность выбора двух будильников. Внешний модуль температуры В комплекте с Oregon Scientific BAR368P идет один внешний беспроводной датчик. Беговая Отличная метеостанция Oregon Weather Home BAR218HG - это - метеостанция - измерение влажности - синхронизация со смартфоном по Bluetooth - беспроводной датчик - часы - прогноз погоды - обычный календарь, лунный календарь - питание автономное на батарейках или аккумуляторах Новая, получена в подарок, открыта, но не использовалась по назначению. Описание: Oregon Scientific BAR310 - метеостанция, измерение влажности, отображение атмосферного давления , беспроводной датчик, часы , прогноз погоды, питание автономное Доставка по городу Москва и другим городам России. RECEPTION SIGNAL To enable and force a signal search: Press and hold for 2 seconds. И, что самое главное на русском языке. Основные кнопки управления собраны на верхней грани. To clear the records: Press and hold MEM for 2 seconds.