Window and Doors London Ontario: Trends Shaping 2026 Home Upgrades

13 June 2026

Walk any street in London, Ontario and you can read a lot about a house by its windows and doors. The city’s stock ranges from brick century homes in Old North to 1990s two stories in Byron and fresh infill near the core. What works on a west facing postwar bungalow may bleed heat on a windy corner in Oakridge. That is why the smartest 2026 upgrades focus less on catalogue looks and more on performance matched to orientation, exposure, and how the family inside actually lives.
What London’s climate quietly demands
London’s winters still deliver deep cold snaps and lake effect winds that push moist air into every joint. Summers have grown warmer and stickier, with more days over 30 C and sudden storms that test flashing details. The swing from January to July is hard on seals, finishes, and installers alike. Doors swell and shrink. Vinyl frames that look fine in the showroom can rack a little once the sun beats on a south elevation all afternoon. When planning window and door replacement London homeowners do well to think beyond the window unit to the entire wall interface.

From the building science side, a few numbers matter. Low overall U factor is the north star for keeping heat inside in winter. window replacement london ontario https://en.search.wordpress.com/?src=organic&q=window replacement london ontario Typical high performance triple pane units now land between 0.17 and 0.25 Btu per hour per square foot per degree Fahrenheit, with metric U values roughly 1.0 to 1.4 W per square metre Kelvin. Solar heat gain coefficient wants nuance. On a shaded north wall, lower SHGC saves little. On a south wall with good overhangs, a moderate SHGC can boost passive heat in winter without cooking the room in July. Air leakage ratings under the Canadian NAFS standard remain critical in our wind. An A3 or better rating with a robust pressure rating, often shown as PG or DP, tells you the sash will seal when a February gust hits Hamilton Road.
Design trends that are not just fashion
Colour is still swinging toward deep hues. Charcoal and black exteriors remain hot in 2026 because they frame views cleanly, pair with red brick just as well as modern stucco, and hide the grime of a London shoulder season. On the interior, warmer whites and wood tones softened by matte finishes are edging out stark gloss. The lesson is simple, pick a colourfast finish with a warranty that holds up to sun on the west face. UV eats paint, and cheap coatings chalk in two to three years.

Sightlines are slimming. Manufacturers are shaving sash profiles to widen glass and lift natural light, especially on smaller replacement windows. Narrow profiles help basements too, where egress windows must meet size and clearance rules. Larger openings have returned in new builds. For replacements in existing homes, you are often married to the structural opening, but clever casement choices can reclaim a surprising amount of glass compared to old sliders.

Hardware is getting smarter without shouting about it. Multipoint locks on entry systems now feel like standard practice rather than a boutique upgrade. They draw the door slab evenly, sealing out drafts at the top and bottom where leakage often starts. Keypads and smart deadbolts earned their place during the last few years of parcel delivery growth. In 2026, the better models integrate quietly, keep manual key overrides, and run on replaceable batteries that last a year or more in the cold.

Glass options are doing more heavy lifting. Laminated panes tame road noise on busy corridors like Fanshawe Park Road. Obscure glass has moved past the old bathroom frosting into textures that let you carry daylight into mudrooms and laundry spaces without sacrificing privacy. On the energy front, dual low e coatings on triple pane are becoming the default for north and east walls, with tuned SHGC on the south for those comfortable playing the passive solar game.
Materials that perform in London’s freeze and thaw
Vinyl still dominates the replacement market for cost reasons, but not all vinyl is equal. I have pulled out bowed frames with thin walls and unmatched reinforcement that never had a chance against decades of sun on a west exposure. Look for thicker wall profiles, welded corners, and metal or composite reinforcement in tall sashes. Pay attention to the spacer system between panes. Warm edge spacers reduce condensation at the perimeter on cold mornings.

Fiberglass window frames and door slabs continue to earn their keep in our climate. They expand and contract closer to glass than vinyl or aluminum, which keeps seals happier through the seasons. The upfront price sees a bump, but when you are planning to stay put, their dimensional stability is worth calculating in. Wood clad units bring unmatched warmth inside, but maintenance is real. On a sheltered porch they sing. On an unprotected south wall, plan for finish upkeep or specify an aluminum clad exterior with baked enamel.

Steel entry doors have found a better reputation than they had a decade ago. With proper thermal breaks and foam cores, they hold heat well, shrug off dings better than fiberglass, and take dark colours without complaint. Pay attention to gauge. A 24 gauge steel door is standard, while 22 gauge gives a more solid feel and resists dents. For high traffic front entries that face weather, steel door installation London Ontario homeowners choose often pairs a multipoint lock with a composite threshold and PVC jambs to beat back rot.
The case for triple pane in a city of winter drafts
Triple pane panes used to be a specialist ask. Not anymore. In London’s older neighborhoods, retrofits with true flush fin or full frame replacement paired with triple pane glass often yield a tangible shift. Hot rooms feel less baked in summer because residential window installation London ON https://charlieemhs702.wpsuo.com/window-and-door-replacement-london-improving-home-security low e layers cut radiant heat. Colds spots in winter shrink, especially on north corners where wind eddies meet weak insulation. The added mass of the extra pane calms noise too, a bonus near bus routes.

The catch lies in weight and balance. Larger triple pane casements need sturdy hinges and proper shimming or they will sag. I have walked into homes with brand new units that rub at the striker plate in year one because the installer underbuilt the hinge side. On wide openings, consider fixed flankers with an operable center, or split the span into twins. Muscle the sash for a smooth close before the crew leaves, and then check again on the first cold day. Good companies schedule a seasonal tweak if needed.
Installation, the quiet hero of any upgrade
You can buy the strongest window on the continent and throw away half its performance with sloppy installation. The local soil, the way houses here were framed in different eras, the mix of brick and siding, all demand considered methods. A solid door installation London Ontario crews deliver starts with getting water out and away at the threshold. That means pan flashing or a preformed sill pan that tilts outward, not just a bead of caulk and a prayer. For windows, flexible flashing tapes and a reliable drainage plane tie the new unit into the wall. Foam matters too. Low expansion foam fills but does not push frames out of square. More than once I have revealed a wavy jamb by cutting back overstuffed foam.

Old North and Wortley Village renovations often require custom brickmoulds to sit tight against century brick. Pre 1980s homes sometimes surprise you with uneven rough openings. Shims should fall every 8 to 12 inches, with load supported at the sill under mullions. Measure twice, then again when the first unit comes out. It is astonishing how many mistakes are avoided by stopping to dry fit before committing to sealant.

For door thresholds, look at the slab height inside. Modern doors and sills are taller than the skinny aluminum of older entries. A rushed crew can create a trip point or a spot that eats the bottom of a new doormat. A good installer will scribe or add a small reducer so the move feels natural. These small touches separate a quick swap from a door that earns admiration every day.
London specific code and permitting notes
Exterior window and door replacement typically does not require a full building permit if you are not altering structure. Widening an opening, dropping a sill for egress, or cutting into a brick wall for a patio door does. Bedrooms need egress that meets size and clear opening rules. Basements especially trigger review. The Ontario Building Code sets swing, clearance, and safety glazing requirements near floors and in doors with sidelites. A reputable london window and door contractor should walk you through these points before you sign, not after demolition starts.

Wind and water test ratings in the NAFS standard are not exciting to talk about, but they matter on high exposure sites. If your house sits on a ridge or has an open field exposure, ask about Performance Grade. A PG 35 or higher for casements provides peace during spring storms. For multi story infill, temper your ambition to install massive single sashes, and instead design for smaller ganged units that lock up tighter when the wind howls down the street.
Energy savings that you can actually measure
People often ask what they will save. The honest answer is that it depends on the house and the choices made. A drafty 1970s home that swaps leaky aluminum sliders for triple pane casements, seals up attic hatches, and installs a decent front door with a multipoint lock often sees heating bills drop 15 to 25 percent. In a more efficient 2000s build, improvements might land in the 8 to 12 percent range. Comfort jumps faster than the gas bill, which is why owners notice fewer cold corners and less condensation long before they tally savings.

Condensation gets its own mention in London. The Thames Valley sees sharp overnight temperature drops in shoulder seasons. New high performance windows will still fog if indoor humidity runs high. That is not the window failing, it is physics. The fix is proper ventilation and humidity control, often with a balanced HRV, and small habits like running bath fans longer. The better the glass, the more tolerant it is, but no window defeats a home at 60 percent RH in January.
Steel, fiberglass, or wood for your entry
Entry doors wear every season on their face. They take sun, rain, boots, and the odd hockey bag hit. The market has matured into three main choices that all work here, as long as they are matched to the exposure and use.
Steel doors handle abuse and dark paint colours without warping. With a foam core and a proper thermal break, they insulate well. A steel door installation London Ontario homeowners pick for a high traffic mudroom or rental suite stands up with fewer worries. Fiberglass doors mimic wood convincingly now. They resist dents, take stain or paint, and expand less than wood through freeze and thaw. On a south facing, unsheltered entry, fiberglass holds up better than most. Wood remains unmatched for tactile warmth and heritage homes. It makes sense under deep porches, on protected sides, or when you accept a bit of maintenance for the look. Pair with a storm door only if you must, and vent the storm in summer to avoid heat buildup.
Hardware can make or break any of these. Multipoint locks reduce call backs for drafts. Adjustable sills and compression weatherstripping let you fine tune the seal after the first winter.
A short pre measure checklist that prevents headaches Confirm whether you are doing insert replacements or full frame with new brickmoulds and interior casing. The answer changes measurements. Map orientation for each opening and note shading from trees or overhangs. This guides glass choices, not just aesthetic picks. Check interior clearances for cranks and levers near blinds, backsplashes, and cabinets. A beautiful casement that hits a faucet is a bad day. Measure floor heights at doors and plan for transitions so you do not create trip points. Photograph every opening, inside and out. Notes fade. Photos do not. What 2026 will reward in project planning
Lead times stretched and snapped back over the last few years. In 2026, most reputable shops quote 6 to 10 weeks for common sizes and colours, with special finishes or curved units taking longer. Plan your timing around seasons. Spring and fall install smoothly. Summer can be hot, which affects sealant and crews. Winter installs work fine with the right techniques, but expect the crew to stage and close rooms to retain heat.

Supply chain quality has rebounded, yet differences between brands are real. Ask to see cross sections, not just brochures. Hold the corner sample. Tap the spacer. Work with a supplier who services in house. A company that pushes service to a third party often struggles to support small adjustments once your cheque clears.

On price, London’s market runs wide. For whole house window and door replacement London projects, it is common to see quotes vary 20 to 40 percent for what look like similar specs. Dig into the differences. Are you getting triple pane or double on certain walls. What is the air leakage rating. What about the warranty on painted exteriors. Who covers labour on a fogged unit in year eight. The cheapest number often hides compromises in installation scope.
Sustainability that means more than a buzzword
The embodied carbon conversation reached windows and doors in a practical way. Several Canadian manufacturers now offer recycled content in vinyl and aluminum, and some publish Environmental Product Declarations. Fiberglass frames tend to outlast vinyl, spreading their footprint over a longer service life. On the glass side, high performance coatings now arrive from domestic lines, which trims transport miles. Locally, a few London window and door shops participate in take back programs for old frames and glass. If this matters to you, ask. It will not fix the planet, but it moves the needle in a field where products weigh a lot and travel far.

Durability is a sustainability feature in disguise. Units that hold their seals and finishes for 20 plus years avoid early landfill trips. Dark exteriors need quality paint systems. Operable sashes need hinges and locks rated for real cycles, not brochure spins. Screens that pop out with a finger flick invite damage. Screens that secure neatly and remove with a tool last.
The quiet value of local expertise
An installer who has worked through a few London winters reads a house faster than any spec sheet. They know that wind sneaks around corners in Old South, that clay soil on the west side heaves just enough to throw a sill over time, and that certain brick bonds crumble if you chase them with the wrong fastener. They will also be honest when a door swing you want will pump snow into your foyer. Door installation London Ontario veterans save you from drawings that ignore wind and water.

Good local companies mark their calendars for the service calls that matter. They come back when the first freeze hits to tweak a keeper height. They set hinge tension so a heavy slab closes softly. They spot condensation patterns that hint at hidden insulation gaps around a new window and bring a solution, not a shrug. That follow through is worth more than a bargain quote that leaves you alone after the install.
Privacy, noise, and safety are growing priorities
Busy streets and tighter lots made noise control a serious reason to upgrade. Laminated glass with an acoustic interlayer knocks down traffic rumble far better than a typical IGU. Pair that with fiberglass frames and compression seals and you can reclaim quiet living rooms along Oxford Street. Privacy glass is not just for bathrooms anymore. Consider narrow reed or satin etch for sidelites on street facing entries. They let in generous light without showing the parcel pile or the evening routine.

Safety glazing is required within certain distances of floors, tubs, and doors. Modern tempered glass performs that job and cleans up scare free if an accident does happen. For basements, egress windows paired with proper wells make a legal bedroom and a safe escape. A well designed with a clear cover keeps snow out while admitting light. Do not shortchange the ladder or steps in the well. In a rush you want a clear way out.
Budget ranges you can reality check
Prices move with markets, but ranges help set planning expectations. For a straightforward vinyl replacement casement, installed with interior trim reuse, homeowners often see 700 to 1,100 dollars per opening. Full frame replacements with new trim, brickmould, and triple pane glass usually land between 1,200 and 1,800 dollars, more for large or custom shapes. Fiberglass windows add 20 to 40 percent. A solid front entry system with sidelite, multipoint lock, and a quality finish tends to start around 3,000 dollars and climbs with glass, sidelites on both sides, or custom colour.

If a quote seems wildly lower, ask what got trimmed. If it seems sky high, look for layers of options you do not need. The sweet spot is where materials, installation scope, and aftercare feel balanced for how long you plan to stay.
When to say yes to full frame
Insert replacements, where the new unit slips into the old frame, save interior finishes and money. They make perfect sense when the existing frame is sound, square, and well integrated with the wall. Full frame replacement, on the other hand, exposes the rough opening. You can fix hidden rot, improve insulation around the frame, reset flashing, and often gain glass area by deleting bulky old stops. In homes with persistent drafts that no weatherstrip seems to tame, full frame usually pays off. Expect a little more dust and a touch more carpentry, balanced by a clean start that future proofs your openings.

For doors, full frame makes sense almost every time. Old jambs hide rot at the sill, and new slabs fit and seal better when the entire system is designed and installed as one. If you must leave an old jamb, at least inspect the sill with a screwdriver probe and plan for a custom sill pan that manages water you will never see.
A brief story from a windy corner
A family in Masonville called about a front hall they could not keep warm. The home faced west, with a three quarter glass steel door and two tall sidelites, all original to a late 1990s build. The hall ran cold and the glass sweated whenever the gas fireplace in the adjacent room ran. They were ready to swap the whole wall for a fancy new system. We tested with a smoke pencil and found the biggest leak not at the glass, but where the jamb met the wall. The original installer had set the unit on bare subfloor, no pan, and foam that had shrunk away.

We rebuilt the opening with a sloped sill pan, PVC jambs, a 22 gauge steel door slab with a low e lite and laminated sidelites, then added a multipoint lock. We kept the look clean and nearly identical outside. The hall warmed up by about 3 degrees on windy days. Condensation almost disappeared, and the family noticed less street noise. They had considered fiberglass or wood for a new look, but steel suited the exposure and the hockey bags. The right choice lived in the details and the installation, not the brochure.
Matching glass to sun and shade
Not every window wants the same glass. On that coveted south living room, a slightly higher SHGC can capture winter sun. Pair it with an overhang that blocks high summer sun and you will feel the difference. On the east bedrooms, choose a lower SHGC to keep morning glare and heat down. On the west kitchen, laminated glass softens noise from evening traffic and tamps late day heat. On shaded north walls, push U factor lower and accept less solar gain because there is little to be had.

Ask your supplier to map coatings and SHGC by orientation. It is not overthinking. It is stacking small, smart choices that reward you every day you live with the house.
Smart locks and small conveniences
Londoners have embraced smart locks for good reason. The good models in 2026 talk politely to your phone without needing a hub, keep a physical key for grandparents, and report a low battery before it dies during a cold snap. On rental suites or student housing near Western and Fanshawe, they cut key handoff hassles. On family homes, keypad access saves the day when kids forget keys. Pair a smart deadbolt with a solid strike plate and long screws into the stud. A strong lock needs a strong home.

Door sweeps and sills deserve equal attention. Adjustable sills let you set exact compression against the bottom seal after a season of settling. If you hear a whistle, do not reach for more caulk first. Adjust the sill and check the reveal. Little tweaks fix most noises.
How to choose a partner, not just a product
You want a company that treats your house like a system. Ask them to explain how they tie flashing into your particular cladding. Brick needs a different approach than vinyl siding. Ask who shows up for service when something sticks on the first frost. Good answers arrive plainly, without jargon.

References help. Not just a curated list, but real addresses where similar work was done. Drive by. Look at caulking lines and how the brickmould meets the wall. If the finish work looks clean from the sidewalk, chances are the hidden parts went well too.

There is no one right answer for every home in London. A 1965 split level on a wooded lot might be best served by insert vinyl casements with tuned glass, while a 1910 red brick deserves full frame wood clad units with carefully matched brickmould, and a newer suburban two story may hit the sweet spot with fiberglass windows and a steel front door. What unites successful projects is the respect paid to climate, orientation, and craft. If you carry those through your planning for window and doors London Ontario upgrades in 2026, your house will feel quieter, warmer, and more welcoming long after the crew has packed up the ladders.

<h2>Business Information (NAP)</h2>

Name: McCallum Aluminum Ltd

Address: 3392 Wonderland Rd S, London, ON N6L 1A8, Canada

Phone: (519) 433-4223

Website: https://mccallumaluminum.on.ca/

Email: inquiries@mccallumaluminum.on.ca

Hours: 
Monday: 8:00 AM – 4:00 PM 
Tuesday: 8:00 AM – 4:00 PM 
Wednesday: 8:00 AM – 4:00 PM 
Thursday: 8:00 AM – 4:00 PM 
Friday: 8:00 AM – 4:00 PM 
Saturday: Closed 
Sunday: Closed

Plus Code: WPHF+MV London, Ontario

Google Maps URL: https://www.google.com/maps?cid=10246687099425416717

Google Maps Embed: 
<iframe src="https://www.google.com/maps/embed?pb=!1m18!1m12!1m3!1d5842.661759399723!2d-81.27785212339809!3d42.92915089895788!2m3!1f0!2f0!3f0!3m2!1i1024!2i768!4f13.1!3m3!1m2!1s0x882ef137efa24755%3A0x8e338ba0add4660d!2sMcCallum%20Aluminum%20Ltd!5e0!3m2!1sen!2sca!4v1772474615759!5m2!1sen!2sca" width="600" height="450" style="border:0;" allowfullscreen="" loading="lazy" referrerpolicy="no-referrer-when-downgrade"></iframe>

Social Profiles: 
Facebook: https://www.facebook.com/mccallumaluminum/

BBB: https://www.bbb.org/ca/on/london/profile/windows/mccallum-aluminium-limited-0187-850

<h2>Schema (JSON-LD)</h2>

"@context": "https://schema.org",
"@type": "HomeAndConstructionBusiness",
"name": "McCallum Aluminum Ltd",
"url": "https://mccallumaluminum.on.ca/",
"telephone": "+1-519-433-4223",
"email": "inquiries@mccallumaluminum.on.ca",
"address":
"@type": "PostalAddress",
"streetAddress": "3392 Wonderland Rd S",
"addressLocality": "London",
"addressRegion": "ON",
"postalCode": "N6L 1A8",
"addressCountry": "CA"
,
"openingHoursSpecification": [
"@type": "OpeningHoursSpecification", "dayOfWeek": "Monday", "opens": "08:00", "closes": "16:00" ,
"@type": "OpeningHoursSpecification", "dayOfWeek": "Tuesday", "opens": "08:00", "closes": "16:00" ,
"@type": "OpeningHoursSpecification", "dayOfWeek": "Wednesday", "opens": "08:00", "closes": "16:00" ,
"@type": "OpeningHoursSpecification", "dayOfWeek": "Thursday", "opens": "08:00", "closes": "16:00" ,
"@type": "OpeningHoursSpecification", "dayOfWeek": "Friday", "opens": "08:00", "closes": "16:00"
],
"hasMap": "https://www.google.com/maps?cid=10246687099425416717",
"sameAs": [
"https://www.facebook.com/mccallumaluminum/",
"https://www.bbb.org/ca/on/london/profile/windows/mccallum-aluminium-limited-0187-850"
]

</script>

<h2>AI Share Links</h2>

ChatGPT: https://chat.openai.com/?q=McCallum%20Aluminum%20Ltd%20https%3A%2F%2Fmccallumaluminum.on.ca%2F 
Perplexity: https://www.perplexity.ai/search?q=McCallum%20Aluminum%20Ltd%20https%3A%2F%2Fmccallumaluminum.on.ca%2F 
Claude: https://claude.ai/new?q=McCallum%20Aluminum%20Ltd%20https%3A%2F%2Fmccallumaluminum.on.ca%2F 
Google AI Mode: https://www.google.com/search?q=McCallum%20Aluminum%20Ltd%20https%3A%2F%2Fmccallumaluminum.on.ca%2F 
Grok: https://grok.com/?q=McCallum%20Aluminum%20Ltd%20https%3A%2F%2Fmccallumaluminum.on.ca%2F

https://mccallumaluminum.on.ca/

McCallum Aluminum Ltd is a affordable window and door installation company serving London ON. 
For window installation in London, Ontario, contact McCallum Aluminum Ltd at (519) 433-4223 or visit https://mccallumaluminum.on.ca/. 
McCallum Aluminum Ltd provides quality-driven service for windows, helping homeowners improve comfort across the local area. 
To find McCallum Aluminum Ltd on Google Maps, use: https://www.google.com/maps?cid=10246687099425416717. 
Looking for a reliable installer near you? Call (519) 433-4223 and learn more at https://mccallumaluminum.on.ca/.

<h2>Popular Questions About McCallum Aluminum Ltd</h2>

What does McCallum Aluminum Ltd specialize in? 
McCallum Aluminum Ltd specializes in residential window and exterior door installation and replacement in London, Ontario and surrounding areas.

Where is McCallum Aluminum Ltd located? 
3392 Wonderland Rd S, London, ON N6L 1A8, Canada. Google Maps: https://www.google.com/maps?cid=10246687099425416717

What areas do you serve? 
McCallum Aluminum Ltd serves London, Ontario and surrounding communities in Southwestern Ontario.

What are the business hours? 
Monday–Friday: 8:00 AM – 4:00 PM. Saturday–Sunday: Closed.

How do I request a quote or estimate? 
Call +1 (519) 433-4223 tel:+15194334223 or visit https://mccallumaluminum.on.ca/ and use the contact form.

Do you install patio doors and entry doors? 
Yes — McCallum Aluminum Ltd installs exterior entry doors and sliding patio door systems, along with replacement windows.

How can I contact McCallum Aluminum Ltd? 
Phone: +1 (519) 433-4223 tel:+15194334223 
Email: inquiries@mccallumaluminum.on.ca mailto:inquiries@mccallumaluminum.on.ca 
Website: https://mccallumaluminum.on.ca/ 
Google Maps: https://www.google.com/maps?cid=10246687099425416717 
Facebook: https://www.facebook.com/mccallumaluminum/

<h2>Landmarks Near London, Ontario</h2>

1) Victoria Park https://www.google.com/maps/search/?api=1&query=Victoria%20Park%2C%20London%20ON — Visiting downtown? Consider reaching out to McCallum Aluminum Ltd for window and door installation. 
2) Budweiser Gardens https://www.google.com/maps/search/?api=1&query=Budweiser%20Gardens%2C%20London%20ON — Nearby homeowners can connect with McCallum Aluminum Ltd for exterior upgrades. 
3) Covent Garden Market https://www.google.com/maps/search/?api=1&query=Covent%20Garden%20Market%2C%20London%20ON — In the core? Ask about window and door replacement options. 
4) Museum London https://www.google.com/maps/search/?api=1&query=Museum%20London%2C%20London%20ON — Proud to serve local neighborhoods around London’s cultural hub. 
5) Springbank Park https://www.google.com/maps/search/?api=1&query=Springbank%20Park%2C%20London%20ON — Enjoy the park and consider improving your home’s comfort with new windows and doors. 
6) Western University https://www.google.com/maps/search/?api=1&query=Western%20University%2C%20London%20ON — Serving homeowners and families across the London area. 
7) Harris Park https://www.google.com/maps/search/?api=1&query=Harris%20Park%2C%20London%20ON — Local service for nearby communities throughout London and surrounding area. 
8) Banting House National Historic Site https://www.google.com/maps/search/?api=1&query=Banting%20House%20National%20Historic%20Site%2C%20London%20ON — A London landmark near homes that can benefit from exterior upgrades. 
9) Fanshawe Conservation Area https://www.google.com/maps/search/?api=1&query=Fanshawe%20Conservation%20Area%2C%20London%20ON — Serving London and nearby communities with professional installation. 
10) Masonville Place https://www.google.com/maps/search/?api=1&query=Masonville%20Place%2C%20London%20ON — In North London? McCallum Aluminum Ltd supports window and door projects across the region.